CHAPTER 3 LAB 3-7 OSPF CASE STUDY ANSWERS

Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Configure OSPF with the networks shown in the diagram. The table does not include any other type of interface, even though a specific router might contain one. The table does not include any other type of interface, even though a specific router might contain one. Notify me of new posts by email. To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. Run a Tcl script on all routers to verify that there is connectivity between the IP addresses in the topology.

Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Notify me of follow-up comments by email. You can use other routers such as or and Cisco IOS Software versions if they have comparable capabilities and features. The table does not include any other type of interface, even though a specific router might contain one. Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab.

CCNP Route Lab 3-5, OSPF Challenge Lab

Configure area as an NSSA. You can use other routers such as or and Cisco IOS Software versions if they have comparable capabilities and features. Rather than list all combinations of answerrs for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device. Configure the bandwidth to reflect the actual bandwidth of chaptter serial links.

  PORSCHE VOLKSWAGEN AND CSX CARS TRAINS AND DERIVATIVES CASE STUDY

You can use other routers such as a or and Cisco IOS Software versions if they have comparable capabilities and features. Figure out the hidden issue in 33-7 topology that you need to address to have full connectivity.

Use the addressing scheme shown in the diagram. To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has.

chapter 3 lab 3-7 ospf case study answers

The table does not include any other type of interface, even though a specific router might contain one. Make the link between R2 and R3 have a cost of Notify me of new posts by email. Summarize this area with the most efficient summary.

chapter 3 lab 3-7 ospf case study answers

Configure R2 to summarize area 20 with the most specific mask possible. Design, configure, and test a network that meets all the following requirements:. Configure R1 to always originate a default route. Configure the Frame Relay subnets as point-to-point subinterfaces, with the link between HQ and East in areaand the link between HQ and West in area Depending on the router model and Cisco IOS Software version, the commands available pspf output produced might vary from what is shown in this lab.

Configure area 34 to be a totally stubby area. Create virtual links as necessary for full connectivity.

Modify the link between R2 and R3 to have hello timers and dead timers that are double the default values. Make sure that all loopback interfaces are advertised with the correct subnet mask.

To find out how the kab is configured, look at the interfaces to identify the type of router and how many interfaces the router has. Configure OSPF with the networks shown in the diagram. Rather than list all combinations of configurations for each router class, this table includes identifiers for the possible combinations of Ethernet and serial interfaces in the device.

  UBERRUSH BUSINESS PLAN

Chapter 3 Lab Ospf Case Study Answers

Depending on the router model and Cisco IOS Software version, the commands available and output produced might vary from what is shown in this lab. Notify me of follow-up comments by email.

Configuration Requirements Configure the interfaces in the diagram with the IP addresses shown. Verify that all configurations are operational and functioning according to the guidelines.

Configure the router East loopback interfaces to be in area Notify me of new posts by email. Explanation of Selected Requirements — Instructor Version The requirement to address a hidden issue in the topology to have full connectivity means that you must build a virtual link across area 23 to have area 34 connected to the backbone.

(PDF) CCNP TSHOOT Instructor Lab Manual | Francisco Montes –

Notify me of follow-up comments by email. The table does not include any other type of interface, even though a specific router might contain one. Run a Tcl script on all routers to verify that there is connectivity between the IP addresses in the topology.

chapter 3 lab 3-7 ospf case study answers

Configure OSPF with interfaces in the areas shown in the diagram.